序号 | 中文 | Chinese Description in English |
1 | 紧固件 | Fastener |
2 | 商品紧固件 | Commercial Fastener |
3 | 标准紧固件 | Standard Fastener |
4 | 非标准紧固件 | Nonstandard Fastener |
5 | 特殊紧固件 | Special Fastener |
6 | 精制紧固件 | Finished Fastener |
7 | 粗制紧固件 | Unfinished Fastener |
8 | 螺纹紧固件 | Threaded Fastener |
9 | 半精制紧固件 | Semi-Finished Fastener |
10 | 有头紧固件 | Headed Fastener |
11 | 无头紧固件 | Headless Fastener |
12 | 压力紧固件 | Compression Fastener |
13 | 高强度紧固件 | High strength Fastener |
14 | 抗剪紧固件 | Shear Fastener |
15 | 抗拉紧固件 | Tension Fastener |
16 | 库存紧固件 | Stock Fastener |
17 | 六角头 | Hexagon head |
18 | 六角头垫圈面 | Hexagon head with washer face |
19 | 六角头凸缘 | Hexagon head with collar |
20 | 六角头法兰面 | Hexagon head with flange |
21 | 方头 | Square head |
22 | 方头、凸缘 | Square head with collar |
23 | 三角头 | Triangle head |
24 | 三角头、凸缘 | Triangle head with collar |
25 | 人角头 | Oct-agonal head |
26 | 12角头、法兰面 | 12 point flange head (bihexagonal head) |
27 | 圆头 | Round head ( button head ) |
28 | 扁圆头 | Mushroom head ( truss head ) |
29 | 圆柱头 | Cheese head ( flat fillister head ) |
30 | 球面圆柱头 | Raised cheese head ( fillister head ) |
31 | 盘头 | Pan head |
32 | 沉头 | Countersunk head ( flat head) ( c s k head ) |
33 | 双沉头 | Reinforced head ( double cone ) |
34 | 半沉头 | Raised countersunk head ( oval head ) |
35 | 球面扁圆柱头 | Binging head |
36 | 沉头清根 | Undercut countersunk head ( undercut flat head ) |
37 | 半沉头清根 | Undercut raised countersunk head ( undercut oval head ) |
38 | 球体头 | Ball head |
39 | 按纽头 | Button head |
40 | 无头 | Headless |
41 | 圆形垫圈头 | Round washer head |
42 | 内六角头 | Socket head |
43 | 高圆头 | High botton head |
44 | 双层头 | Biconic head |
45 | 锥头 | Cone head |
46 | 尖锥头 | Steeple head |
47 | 喇叭头 | Bugle head |
48 | 薄片头 | thin wafer |
49 | 冲压凹穴型头 | Drilled fillister head |
50 | 伞形头 | Stuss head |
51 | 蘑菇头 | Mushroom head |
52 | 支承面 | Bearing surface |
53 | 垫圈面 | Washer face |
54 | 六角 | Hexagon |
55 | 四方 | Square |
56 | 三角 | Triangle |
57 | 人角 | Octagon |
58 | 内六角 | Hexagon socket |
59 | 内三角 | Triangle socket |
60 | 内四角 | Square socket |
61 | 内六花键 | Six-spline socket |
62 | 开槽 | Slot |
63 | 十字槽 | HCross recess ( phillips ) |
64 | 十(米)字槽 | Cross recess ( pozidriv ) |
65 | 蝶形(翼形) | Wing |
66 | 旋棒 | Tommy |
67 | 直纹滚花 | Straight knurl |
68 | 网纹滚花 | Diamond knurl |
69 | 十字孔 | Cross hole ( set pin hole in side ) |
70 | 五角 | Pentagon |
71 | 梅花槽 | Torx recess |
72 | 离合槽 | Clutch recess |
73 | 四方槽 | Square recess |
74 | 标准杆 | Normal shank ( nominal shank diameter=nominal thread diameter) |
75 | 细杆 | Reduced shank ( shank diameter<minor diameter ) |
76 | 腰状杆 | Waisted shank ( shank diameter> thread diameter ) |
77 | 加强杆 | Increased shank ( shank diamerer> thread diameter ) |
78 | 轴杆 | Shouder ( collar ) |
79 | 方颈 | Square neck |
80 | 榫 | Fin |
81 | 凸缘 | Fillet |
82 | 锯齿形 | Serration |
83 | 肋 | Lug |
84 | 条颈 | Ribbed neck |
85 | 胀大颈 | Swell neck |
86 | 杆(部)体 | Shank |
87 | 锥端 | Cone point |
88 | 截锥端 | Short dog point |
89 | 凹端 | Cup point |
90 | 短圆柱端 | Short dog point |
91 | 长圆柱端 | Long dog point |
92 | 短圆柱球面端 | Short dog point with rounded end |
93 | 短圆柱截锥端 | Short dog point with truncated cone end |
94 | 刮销端 | Scrape point |
95 | 自攻螺钉的末端 | End for self-tapping screws |
96 | 自攻锁紧螺钉的末端 | End for thread rolling screws (thread formed by deformation ) |
97 | 辗制末端 | As-roller end |
98 | 平端 | Flat point |
99 | 球面端(倒圆端) | Rounded end |
100 | 倒角端 | Chamfered end |
101 | 钻孔端 | Gimlet point |
102 | 顶锻端 | Header point |
103 | 钉子端 | Nail point |
104 | 针端 | Needle point |
105 | 半圆端 | Oval point |
106 | 导向端 | Pilot point |
107 | 球端 | Spherical point |
108 | 夹断端 | Pinck point |
109 | 实际尺寸 | Actual size |
110 | 允差 | Allawance size |
111 | 基本尺寸 | Basic size |
112 | 设计尺寸 | Design size |
113 | 配合 | Fit |
114 | 尺寸极限 | Limits of size |
115 | 公称尺寸 | Nominal size |
116 | 参改尺寸 | Reference size |
117 | 公差 | Tolerance |
118 | 公差位置 | Position tolerance |
119 | 对边宽度 | Width across flats |
120 | 对角宽度 | Width across corner |
121 | 螺纹通(测量) | Go thread gauge |
122 | 螺纹止(测量) | No go thread gauge |
123 | 头下圆角半径 | Radius under head |
124 | 开槽宽度 | Slot recess width |
125 | 开槽深度 | Slot recess depth |
126 | 十字槽插入深 | Penetration depth |
127 | 十字槽直径 | Recess diameter |
128 | 十字槽宽度 | Recess width |
129 | 头部直径 | Head diameter |
130 | 头部高度 | Head height |
131 | 头部角度 | Head angle |
132 | 无螺纹杆径 | Shank diameter ( unthreaded diameter ) |
133 | 无螺纹杆长 | Shank length ( unthreaded length ) |
134 | 夹紧长度 | Grip length |
135 | 螺纹大径 | Major thread diameter |
136 | 螺纹小径 | Minor diameter ( small ) |
137 | 肩距 | Unthreaded length under head |
138 | 螺纹长度 | Thread length |
139 | 杆长 | Total length |
140 | 内六角扳拧深度 | Depth hexagon socket |
141 | 内凹槽插入深度 | Key engagement |
142 | 外径 | Exter diameter ( outside diameter ) |
143 | 内径 | Internal diameter ( inside diameter ) |
144 | 长度 | Length |
145 | 宽度 | Breadth |
146 | 厚度 | Thickness |
147 | 高度 | Hight |
148 | 孔径 | Bore diameter |
149 | 法兰直径 | Flange diamerer |
150 | 方径长度 | Square neck length |
151 | 方径宽度 | Square neck width |
152 | 凸缘高度 | Collar height |
153 | 凸缘直径 | Collar diameter |
154 | 对称度 | Symmerty |
155 | 同轴度 | Concentricity ( coaxiality ) |
156 | 垂直度 | Perpendicularity |
157 | 平行度 | Parallelism |
158 | 直度 | Straightriess |
159 | 槽杆同轴度 | Recess concentricity |
160 | 头杆同轴度 | Head concentricity |
161 | 头杆垂直度 | Head lnclination |
162 | 斜度 | Angularity ( taper ) |
163 | 弧度或弯曲度 | Bow or camber |
164 | 尾尖角 | Point angle |
165 | 镀锌层厚度 | Zinc plating thickness |
166 | 跳动 | Run-out |
167 | 锥度 | Taper ratio |
168 | 榫长 | Nib length |
169 | 榫宽 | Nib width |
170 | 倒角.圆角 | Chamfer |
171 | 平面度 | Flatness |
172 | 抗拉强度 | Tensile strength |
173 | 屈服强度 | Proof strength |
174 | 屈服点 | Lower yield stress |
175 | 扭转强度 | Torque strength ( torsional strength ) |
176 | 剪切强度 | Shear strength |
177 | 冲击韧性 | Impact strength |
178 | 延伸率 | Elongation |
179 | 断面收缩率 | Reduction |
180 | 拉(压)应力 | Tension |
181 | 破坏(扭)力矩 | Breaking torque |
182 | 晶粒度 | Grahularity |
183 | 机械性能 | Mechanical properties |
184 | 脱碳 | Decarburise |
185 | 渗碳 | Carburization |
186 | 最小剩余弹力 | Minimum residual sping force |
187 | 压负荷的百分率 | Percenatage of compression load |
188 | 表面硬度 | Surface hardness |
189 | 芯部硬度 | Core hardness |
190 | 扭矩 | Torque ( torsion ) |
191 | 表面硬化层深度 | Case harden depth |
192 | 氢脆 | Hydrogen embrittlement |
193 | 压载(负)荷 | Compression load |
194 | 硬度试验 | Hardness test |
195 | 头部坚固性试验 | Head soundness test |
196 | 扭转试验 | Twisting test |
197 | 弹性试验 | Resilience test |
198 | 保证载荷试验 | Proof loading test |
199 | 楔负载强度试验 | Wedge loading test |
200 | 弯曲试验 | Bending test |
201 | 旋入试验 | Screw-in test |
202 | 最小破坏力矩试验 | Torsional test and minimum torques |
203 | 永久变形试验 | Permanent deformation test |
204 | 盐雾试验 | Salt spray test |
205 | 弹性 | Elasticity |
206 | 韧性 | Tenacity ( Toughnee ) |
207 | 塑性 | Fiexibility |
208 | 磁力碳伤 | Magnetic particle inspection |
209 | 碳钢 | Carbon steel |
210 | 低碳钢 | Low carbon steel |
211 | 中碳钢 | Medium carbon steel |
212 | 合金钢 | Alloy steel |
213 | 热处理钢 | Heat-treated steel |
214 | 低马钢 | Low carbon martensite steel |
215 | 奥氏体不锈钢 | Austenitic stainless steel |
216 | 马氏体不锈钢 | Martenitic stainless steel |
217 | 铁 | Iron |
218 | 铝 | Aluminium |
219 | 黄铜 | Brass |
220 | 紫铜 | Copper |
221 | 青铜 | Bronze |
222 | 塑料 | Plastic |
223 | 淬火 | Quenched |
224 | 回火 | Tempered |
225 | 退火 | Annealed |
226 | 表面硬化 | Case hardened |
227 | 强度等级 | Class |
228 | 氧化 | Oxide ( anodizing ) |
229 | 金属 | Metal |
230 | 非金属 | Metalloid |
231 | 发黑 | Black |
232 | 本色 | Plain ( self colour ) |
233 | 热处理 | Heat treatment |
234 | 涂层 | Coating |
235 | 表面处理 | Finish |
236 | 涂蜡 | Waxed |
237 | 镀锌(兰白锌) | Zinc plated ( zinc / clear ) |
238 | 镀黄锌 | Zinc yellow ( Y.Z.P.) |
239 | 镀黑锌 | Zinc plated black |
240 | 镀镍 | Nickel plated |
241 | 镀铜 | Brass plated |
242 | 热浸镀锌 | Hot dip galvanized ( H.D.G.) |
243 | 电镀 | Electplating |
244 | 机械镀锌 | Mechanical galvaizing |
245 | 表面热处理 | Surface heat treatment |
246 | 冷镦 | Cold heading |
247 | 冷锻 | Cold forging |
248 | 热锻 | Hot forging |
249 | 成型 | Forming |
250 | 切削(断) | Cutting |
251 | 缩径 | Shrink diameter |
252 | 搓(攻)丝 | Threading |
253 | 滚丝 | Thread rolling |
254 | 拔丝 | Drawing |
255 | 酸洗 | Pickling |
256 | 钝化 | Passirating |
257 | 废水处理 | Waste water treatment |
258 | 研磨 | Grinding |
259 | 镦粗 | Upsetting |
260 | 开槽 | Soltting |
261 | 刮削 | Sharing |
262 | 滚花 | Kunrling |
263 | 抛光 | Polishing |
264 | 冲压 | Punching |
265 | 滚动 | Tumbling |
266 | 精整 | Trimming |
267 | 铣削 | Milled |
268 | 挤压 | Extruding |
269 | 钻孔 | Drilling |
270 | 模压 | Embossing |
271 | 沉孔 | Countersinking |
272 | 压印 | Coining |
273 | 扩孔 | Counterboring |
274 | 控削 | Broaching |
275 | 辊光 | Burnishing |
276 | 锻造 | Forging |
277 | 剪切 | Shear |
278 | 焊接 | Welded |
279 | 喷砂 | Sand blasting |
280 | 裂缝 | Cracks |
281 | 淬火裂缝 | Quench cracks |
282 | 锻造裂缝 | Forging cracks |
283 | 锻造爆裂 | Forging bursts |
284 | 剪切爆裂 | Shear bursts |
285 | 条痕 | Laps |
286 | 凹痕 | Voids |
287 | 皱纹 | Folds ( pits ) ( laps ) |
288 | 切痕 | Tool marks |
289 | 损伤 | Damages |
290 | 毛刺 | Burr |
291 | 碎屑 | Chip |
292 | 夹杂 | Inclusions |
293 | 锈皮 | Sharing |
294 | 飞边 | Flash |
295 | 开裂 | Cracks |
296 | 锈、锈斑 | Rust |
297 | 普通螺纹 | Screw thread |
298 | 锥螺纹 | Taper screws thread |
299 | 自攻螺纹(宽牙螺纹) | Tapping screws thread ( spaced thread ) |
300 | 木螺钉螺纹 | Wood screws thread |
301 | 米制螺纹 | Metric thread |
302 | ISO米制螺纹 | ISO Metric thread |
303 | 米制细牙螺纹 | Metric fine pitch thread |
304 | ISO米制细牙螺纹 | ISO Metric fine pitch thread |
305 | 寸制螺纹 | Inch thread |
306 | 统一螺纹(ISO寸制) | Unified screw thread ( ISO inch ) |
307 | 惠氏螺纹 | Whitworth thread |
308 | 管螺纹 | Pipe thread |
309 | 惠氏管螺纹 | Whitworth pipe thread |
310 | 螺旋线 | Helix |
311 | 螺旋面 | Helical surface |
312 | 外螺纹 | External thread |
313 | 内螺纹 | Inernal thread |
314 | 牙侧 | Flank |
315 | 沟槽 | Groove |
316 | 凸起 | Ridge |
317 | 牙顶 | Crest |
318 | 牙底 | Root |
319 | 螺纹牙型 | Thread profile |
320 | 螺纹线 | Thread |
321 | 单线螺纹 | Single–start–thread |
322 | 多线螺纹 | Multi–start–thread |
323 | 右旋螺纹 | Right–start–thread |
324 | 左旋螺纹 | Left–start–thread |
325 | 工作牙侧 | Pressure ( load ) flank |
326 | 非工作牙侧 | Clearing ( clearance ) flank |
327 | 牙底的圆角半径 | Root radius |
328 | 牙型高度 | Height ( or depth ) of thread |
329 | 牙型角 | Included angle |
330 | 牙型半角 | Flank lead |
331 | 中径线 | Pitch line |
332 | 螺纹轴线 | Axis of thread |
333 | 导程 | Flank lead |
334 | 双牙导程 | Dual flank lead |
335 | 螺距 | Flank pitch |
336 | 双牙螺距 | Dual flank lead |
337 | 大径 | Major diameter |
338 | 小径 | Minor diameter |
339 | 中径 | Pitch diameter |
340 | 单一中径 | Simple pitch diameter |
341 | 作用中径 | Virtual pitch diameter |
342 | 螺纹升角 | Lead angle |
343 | 基本牙型 | Basic profile |
344 | 伞状螺纹 | Umbrella thread |
345 | 粗牙螺纹 | Coarse thread |
上一篇: 膨胀螺丝的技术使用方法
下一篇: 紧固件具体包含了哪些产品?
您好!请登录